Home Back My Cart : 0 item(s)


3D Holographic Gloss Black Carbon Fiber Wrap Vinyl With Air Release

3D Holographic Gloss Black Carbon Fiber Vinyl Wrap With Air Release
Price: $22.99
Product ID : CF3DH1
Weight: 1.00 lbs

Special Offer

Purchase 2 of 3D Holographic Gloss Black Carbon Fiber Wrap Vinyl With Air Release and get:

A $3.99 VALUE!


  • Buy 2 - 5 and get an additional 10 % off
  • Buy 6 - 10 and get an additional 15 % off
  • Buy 11 - 20 and get an additional 20 % off
  • Buy 21 - 30 and get an additional 25 % off
  • Buy 31 - 40 and get an additional 30 % off
  • Buy 41 - 1,000 and get an additional 35 % off

Min/Max Order: 1 / 1000


3D Holographic Gloss Black Carbon Fiber vehicle wrap vinyl is cut from a 60" wide roll and is sold by the foot. Price starts at $22.99 for the 1st linear foot. Each quantity purchased is for 1 linear foot, or 12 inches long. You'll receive one continuous sheet when you order more than 1 linear foot. For example, to order a 60 " wide x 72" long sheet, you would enter "6" in the Quantity textbox above. Purchase 2 linear feet or more and get additional discount.

The 3D holographic gloss black carbon fiber is brand new! This is the most realistic looking carbon fiber wrap vinyl we have to offer. The carbon fiber is textured like the rest you see in the market, including brand names like 3M, Oracal, Avery. But what makes it more realistic looking than all of these is that there are tiny patterns of concentric circles embedded within the textured twill weave carbon fiber design. As light hits the carbon fiber design, the carbon fiber appears "holographic" and 3 dimensional looking, just like real carbon fiber. Unrealistically real! It is just amazing! Wish we could capture with a photo to prove our point. The pics can't show you what we are saying. You just have to see it in person. Sample is available for purchase, Click Here.

3D holographic gloss black carbon fiber can be applied to any hard smooth surface such as such as front hood, rear trunk, spoiler, lips, side pillar bars, rims, side mirrors, door handles, windshield, interior trim, cell phones, laptop, speakers, etc.

Notes: Install in a clean area, away from dust and wind. Application surface should be cleaned with soap and water or other cleaning agents. Cleaning agents must NOT contain ammonia (like Windex) as these will dissolve the adhesive. On complex curves and edges, apply heat for better adhesion and conformity to curved surface. 3M Primer 94 is recommended for application involving sharp edges or extreme curves. For a more glossy look, apply a high quality clear coating.

  • Permanent acrylic pressure-sensitive adhesive
  • Air Egress Technology
  • Lay-flat, bubble free installation
  • Dry Application. No messy water/soap solution needed!
  • Can be re-lifted, repositioned and stretched
  • Textured pattern, WITH WEAVES! NOT PRINTED! GLOSSY!
  • 3D Holographic Effect! Unrealistically real carbon fiber look!
  • Stretchable with heat
  • Conform to contours and bend easily
  • High temperature & water resistant
  • Install Temp: 60F to 80F (16C to 26C)
  • End Use Temp: -4F to 206F (-15C to 97C)
  • Can be cleaned with soap and water
  • Stands up against water, dirt, grease, salt, mild acids and oil.
  • Long life with excellent UV durability: 3-5 yrs outdoor/unlimited indoor
  • Design for auto wrapping, 7.5 mil (.0075" thick film)
Note: The videos below are for instructional purpose only. We also carry 3M DI-NOC carbon fiber.

More images

Recommended Products


Products You May Like

Call us: (504) 208-4846

Full Website